![]() After that, hit Login to add your camera to Reolink Client. Then input the Username (admin by default), the camera Password. For the E1 series camera, Lumus, and battery-powered camera, which have connected to your network successfully, please click Wi-Fi Already Configured and click Confirm. See How to find the UID of your device, click Add. Please select the SSID (network name) of your router that you would like to connect and type in the WiFi password. Click the "+" icon, fill in the blanks with the UID of your camera. Please refer to the video below to add cameras or NVR via Reolink Client. Find your Reolink Doorbell camera from the list of All Devices. ![]() Open the Amazon Alexa app on your mobile device, and go to Devices > All Devices. See how to forward ports on your router interface. Here is also a video for your reference to add Reolink camera to Amazon Alexa: Set up Your Alexa Device as A Doorbell Chime. If you're using the Domain Name/IP Address to access the cameras, please ensure that the port-forwarding settings on your router are correct. How to Initial Setup for Reolink E1 Series Cameras / Reolink Lumus via Reolink Client (New Client)Ĥ. How to Initially Set up Reolink 4G Cameras via Reolink Client (New Client)ģ. How to Initially Set up Battery-powered Cameras via Reolink Client (New Client) If you haven't connected it to your network, please check ![]() Reolink battery-powered cameras only support UID for remote access. It is suggested to use the UID for remote access.Ģ. (4) Adjust the camera direction as needed by panning and tilting it through the Reolink App or Client.1. (3) Power the camera by connecting its charging cable to the longer cable on the bracket. (1) Drill holes with the mounting hole template. For details, see the following instructions. Install the camera separately from the solar panel. (3) Connect the camera’s charging cable to the longer cable on the bracket. (2) Fix the upper part with the screwdriver and two screws. (1) Secure the lower part of the camera bracket using a screwdriver and two screws. Attach the camera to the mounting bracket for better waterproof performance. Ensure that the arrows on the two cables are aligned. Connect the cable from the panel to the shorter cable on the bracket. Once determined, tighten the screws firmly to maintain the desired angle. Loosen the four screws on both sides of the solar panel’s bracket and find the angle that receives maximum sunlight. Use the provided hex key to tighten the screws and secure the panel in place. Then when you can view the playback through the NVR once they are added. Like taw94 said, you need to add the cameras to the NVR via a monitor attached to the NVR. You cannot add cameras to the NVR in the app or client. Install the solar panel onto the bracket. You can only add cameras directly to the NVR with a monitor and mouse connected. Use the provided open-end wrench to tighten the screws to secure the bracket. Insert the included anchors, and attach the mounting bracket to the mounting surface. Drill holes in the desired mounting surface according to the mounting template. Attach the camera mounting base to the mounting bracket with two screws. ![]() Note: For optimal detection, install the camera in the direction crossing intruders' movement path instead of facing it, otherwise, the camera may fail to detect motion. Install the camera 2–3 meters (7-10 ft) above ground to maximize the detection range of the PIR motion sensor. Factors such as weather conditions, seasonal changes, and geographic location can affect the amount of energy produced by the solar panel. Note: The Reolink solar panel needs only a few hours of direct sunlight to power up your camera daily. Choose a location where the solar panel can get the most sunlight throughout the year. Please follow the step-by-step instructions below for a successful installation. To ensure proper operation of Reolink TrackMix LTE Plus, it is necessary to install it with the Reolink Solar Panel Plus for power supply.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |